1.05 is really outdated, latest is 1.11, perhaps you use atmel or other hardware and use other repos that i can see?
Temperature CPU?
-
- OMV 1.0
- joq3
-
-
1.05 is really outdated, latest is 1.11, perhaps you use atmel or other hardware and use other repos that i can see?
Don't know, just installed trough OMV-Extra's which is version 1.30. Are notifications possible in version 1.11? Any way I can update?
-
-
Zitat von sheriff
Don't know, just installed trough OMV-Extra's which is version 1.30. Are notifications possible in version 1.11? Any way I can update?
enable omv-extras.org testing to gain access to latest ( testing version), actually temperature CPU is in active development and still not promoted as "stable".
-
I'm in the same situation... I can only see 1.0.5 and the testing repos are active...
-
If you are running Openmediavault 2 then you have to enable the downloader testing repo. If that don't work then uninstall sensors plugin and check after the plugin again. That worked for me.
-
Had a problem adding the latest version (1.0.13)
This version has the system fan monitor enabled as well as the option to stop showing the CPU cores.
While testing the system fan I have noticed an issue where it is difficult to get the exact system fan as most MB's have at least 2 connections available, I am thinking of a work around but for now just wanted to get a version out with it enabled. -
I'm on OMV 1 and even after uninstall I can only see 1.0.5
I have refreshed the repos and cheched for new updates several times but no luck so far. -
guys, will be this plugin available also for OMV 1.19 for RPi2?
i found out this weekend, that my RPi2 was overheated several times, coz in our country is too hot weather and i must cancel my overclock from 1000MHz to default 700Mhz
-
I can only make packages for a single repo (stoneburner) so another dev needs to build the package for OMV 1
Mio, does the Rpi2 have sensors, you can install the 1.0.5 version and run the commands I mention a few pages back.
-
-
-
im using this command, not lm-sensors:
root@raspberrypi:~# /opt/vc/bin/vcgencmd measure_temp
temp=42.8'Cin graphs i cannot see option with temps
-
You will not see any temp graphs unless you install the plugin, not sure if it will show up on your system as I do not have a Rpi2 to check on. it should be in the omv extras download managers testing repo.
-
an error during installation:
Code
Alles anzeigenReading package lists... Building dependency tree... Reading state information... The following NEW packages will be installed: openmediavault-sensors 0 upgraded, 1 newly installed, 0 to remove and 1 not upgraded. Need to get 52.5 kB of archives. After this operation, 221 kB of additional disk space will be used. WARNING: The following packages cannot be authenticated! openmediavault-sensors Authentication warning overridden. Get:1 http://packages.omv-extras.org/debian/ kralizec-testing/main openmediavault-sensors all 1.0.5 [52.5 kB] Fetched 52.5 kB in 1s (52.0 kB/s) Selecting previously unselected package openmediavault-sensors. (Reading database ... 45207 files and directories currently installed.) Unpacking openmediavault-sensors (from .../openmediavault-sensors_1.0.5_all.deb) ... ================= Error ================= Failed to load configuration (Fatal error 77: Premature end of data in tag mntentref line 443 (line=443, column=38); Fatal error 77: Premature end of data in tag sharedfolder line 439 (line=443, column=38); Fatal error 77: Premature end of data in tag shares line 406 (line=443, column=38); Fatal error 77: Premature end of data in tag system line 6 (line=443, column=38); Fatal error 77: Premature end of data in tag config line 2 (line=443, column=38))========================================= Processing triggers for openmediavault ... Restarting engine daemon ... Setting up openmediavault-sensors (1.0.5) ... Initial configuration. Processing triggers for openmediavault ... Updating locale files ... Updating file permissions ... Purging internal cache ... Restarting engine daemon ... Creating index of upgradeable packages ... Creating index of OpenMediaVault plugins ... Done ...
-
installed and activated... but nothing new in graphs... should i reboot the server? or the error is important?
-
Try running sensors in a shell if you do not get any output try again after running omv-sensors-detect
-
I can only make packages for a single repo (stoneburner) so another dev needs to build the package for OMV 1
Mio, does the Rpi2 have sensors, you can install the 1.0.5 version and run the commands I mention a few pages back.
thanks jhmiller, this clarifies it!
-
-
Thanks to @davidh2k the new version (1.0.13) should be in the repo now.
is this for OMV 1 or OMV 2?
Jetzt mitmachen!
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!