Is there anyway I can get the storage->s.m.a.r.t GUI to display the smart status of my HP array?
I've upgraded the smartmontools package to v6.4 from the wheezy-backports repository and I can query the smart status of the individual drives without issue.
root@storage:/etc# smartctl /dev/sg1 -a -d cciss,0
smartctl 6.4 2014-09-29 r3990 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sg1 [cciss_disk_00] [SAT]: Device open changed type from 'sat,auto+cciss' to 'sat'
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 5K3000
Device Model: Hitachi HDS5C3020ALA632
Serial Number: ML0220F31DZZ5N
LU WWN Device Id: 5 000cca 369d4003a
Firmware Version: ML6OA580
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5940 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed May 20 14:21:44 2015 AEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22966) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 383) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 134 134 054 Pre-fail Offline - 100
3 Spin_Up_Time 0x0007 153 153 024 Pre-fail Always - 376 (Average 342)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 115
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 146 146 020 Pre-fail Offline - 29
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 28883
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 102
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 116
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 116
194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Min/Max 16/50)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Alles anzeigen
The problem I have is that no matter what changes I make to smartd.conf, the GUI always incorrectly shows /dev/sda (which is the logical disk).
I've tried adding the following to /etc/default/openmediavault and rebooting, but it doesn't seem to make a difference
After adding the -d option I get the following if I attempt to save any changes from the GUI;
Failed to execute command 'export LANG=C; omv-mkconf smartmontools 2>&1': /usr/sbin/omv-mkconf: 51: /etc/default/openmediavault: -d: not found
Can anyone point me in the right direction to be able to get this displayed in the GUI?
Where does the GUI enumerate the information for the drives it displays and can this be modified?
I've already added the HP RAID package from OMV-Extras, but this doesn't provide an email mechanism, to let me know when a drive is faulty.
I've also tried upgrading to stone burner as I see other people with other RAID controllers had their issue resolved by upgrading, but it didn't make a difference.
Thanks.