My ATA error count on two drives keep increasing due to what I believe is an ABRT Error. I have pasted the SMART Logs for the drive bellow. Should I start to be worried about this or is it something I can ignore for now?
Code
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 140 140 021 - 15000
4 Start_Stop_Count -O--CK 100 100 000 - 10
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 91
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 10
192 Power-Off_Retract_Count -O--CK 200 200 000 - 6
193 Load_Cycle_Count -O--CK 200 200 000 - 50
194 Temperature_Celsius -O---K 095 091 000 - 57
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+23:45:53.762 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+23:45:53.762 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+23:45:53.762 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+23:45:53.761 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+23:45:53.761 SMART READ LOG
Error 4 [3] occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 1d+22:09:19.796 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.796 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.796 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.795 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 1d+22:09:19.795 SMART READ LOG
Error 3 [2] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 10:43:56.886 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 10:43:56.886 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 10:43:56.885 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 10:43:56.885 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 10:43:56.885 SMART READ LOG
Error 2 [1] occurred at disk power-on lifetime: 43 hours (1 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:18:17.086 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:18:17.086 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:18:17.086 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:18:17.085 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:18:17.085 SMART READ LOG
Error 1 [0] occurred at disk power-on lifetime: 37 hours (1 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:53:34.333 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 08:53:34.333 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 08:53:34.332 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:53:34.331 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 08:53:34.331 SMART WRITE LOG
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 57 Celsius
Power Cycle Min/Max Temperature: 27/61 Celsius
Lifetime Min/Max Temperature: 27/61 Celsius
Under/Over Temperature Limit Count: 0/139
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (455)
Index Estimated Time Temperature Celsius
456 2014-09-29 18:58 57 **************************************
... ..(476 skipped). .. **************************************
455 2014-09-30 02:55 57 **************************************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 171928 Vendor specific